מדריך הוראות להבי מכסחת דשא מקוריים של Toro מדגם 105-7718-03 בגודל 60 אינץ'

1. הקדמה

This instruction manual provides important information regarding the proper installation, safe operation, and maintenance of your new Toro Genuine OEM 105-7718-03 60-inch Flow Lawn Mower Blades. Please read this manual thoroughly before attempting any installation or maintenance procedures to ensure safe and effective use of the product.

2. המוצר נגמרview

These are genuine OEM replacement blades designed for Toro 60-inch flow lawn mowers. They are engineered to provide optimal cutting performance and durability.

Figure 2.1: Set of three Toro Genuine OEM 105-7718-03 lawn mower blades.

תכונות עיקריות:

• Genuine OEM quality ensures precise fit and performance.
• Designed for 60-inch flow lawn mower decks.
• Constructed for durability and efficient cutting.

3. תאימות

These blades are compatible with Toro 60-inch flow lawn mowers and are direct replacements for OEM part numbers 105-7718, 108-1114, and 105-7718-03. It is crucial to verify your unit's model, specification, type/code, and serial number to ensure correct fitment. If you are uncertain about compatibility, please consult your mower's manual or contact a qualified service technician.

מחליף מספרי חלק:

• 105-7718-03
• 105-7718
• 108-1114

4. מפרטים

Figure 4.1: Blade length measurement.

Figure 4.2: Blade width and center hole measurements.

Figure 4.3: Close-up of blade markings for identification.

5. מידע בטיחות

WARNING: Always disconnect the spark plug wire(s) or remove the battery before performing any maintenance or installation on your lawn mower to prevent accidental starting.

• Wear heavy-duty gloves when handling mower blades, as edges can be sharp.
• ללבוש הגנה מתאימה לעיניים.
• Ensure the mower is on a flat, stable surface and secured to prevent movement.
• Allow the engine and blades to cool completely before servicing.
• Refer to your lawn mower's owner's manual for specific safety instructions and procedures.

6. התקנה

Follow these general steps for replacing your lawn mower blades. Always consult your specific mower's owner's manual for detailed instructions and torque specifications.

1. הכנת מכסחת הדשא: Park the mower on a level surface. Turn off the engine, remove the ignition key, and disconnect the spark plug wire(s) or remove the battery to prevent accidental starting.
2. גישה ללהבים: Depending on your mower type, you may need to raise the front of the mower or remove the cutting deck. Use appropriate lifting equipment or stands for safety.
3. הסר להבים ישנים: Use a block of wood to prevent the blade from turning. With a wrench, loosen and remove the blade bolt(s) holding the old blade in place. Note the orientation of the old blade for correct installation of the new one.
4. בדוק רכיבים: Check the blade spindle, washers, and bolts for wear or damage. Replace any worn components.
5. התקנת להבים חדשים: Position the new blade with the cutting edge facing the correct direction (usually indicated by a curve or stamp). Ensure the blade is properly seated on the spindle.
6. להבים מאובטחים: Reinstall the blade bolt(s) and washers. Tighten the bolt(s) to the torque specification provided in your mower's owner's manual. Overtightening or undertightening can cause damage or unsafe operation.
7. להרכיב מחדש ולבדוק: Reattach the cutting deck (if removed) and reconnect the spark plug wire(s) or battery. Start the mower and listen for any unusual vibrations or noises. If present, turn off the mower immediately and re-check installation.

7. הפעלה

Once the new blades are installed, ensure they are balanced and properly torqued. Operate your lawn mower according to its owner's manual. New blades will provide a cleaner cut, which is beneficial for grass health. Avoid mowing over obstacles that could damage the blades.

8. תחזוקה

Regular maintenance of your mower blades is essential for optimal performance and longevity.

• ניקוי: After each use, clean grass clippings and debris from the blades and underside of the mower deck. This prevents rust and maintains balance.
• הַשׁחָזָה: Blades should be sharpened regularly, typically after every 20-25 hours of mowing, or more frequently if you notice frayed grass tips after cutting. Use a blade sharpener or take them to a professional. Ensure blades are balanced after sharpening.
• בְּדִיקָה: Periodically inspect blades for bends, cracks, or excessive wear. Replace damaged blades immediately to prevent further damage to the mower or injury.

Figure 8.1: Properly sharpened blade edge.

9. פתרון תקלות

If you experience issues after installing new blades, consider the following:

• איכות חיתוך ירודה: Ensure blades are sharp, installed with the correct orientation, and the mower deck is level.
• רטט מוגזם: This often indicates an unbalanced or bent blade. Remove and inspect blades for damage or proper balancing. Re-torque blade bolts.
• Mower Stalling/Loss of Power: Check for excessive grass buildup under the deck or if blades are incorrectly installed, causing too much drag.

10. אחריות ותמיכה

For warranty information or technical support regarding your Toro Genuine OEM blades, please refer to the documentation provided with your original mower or contact Toro customer service directly. Always provide your product model and serial number when seeking support.