RJ45 Crimp Tool Ethernet Crimper Instruction Manual

1. הקדמה

This instruction manual provides detailed guidance for the proper use and maintenance of your PETECHTOOL RJ45 Crimp Tool Set. This comprehensive kit is designed for various network wiring needs, including the creation and testing of custom-length Ethernet cables. It supports 8P8C RJ45 Cat6, Cat6a, Cat5e, Cat5 connectors and 6P6C RJ12 modular connectors (excluding AMP). Please read this manual thoroughly before operation to ensure safe and efficient use.

2. מידע בטיחות

Always observe the following safety precautions when using the RJ45 Crimp Tool Set:

• הרחק את הכלים מהישג ידם של ילדים.
• יש ללבוש ציוד מגן אישי מתאים, כגון משקפי בטיחות, כדי להגן מפני פסולת מעופפת.
• ודא שאזור העבודה מואר היטב וללא מכשולים.
• Do not use the tools for purposes other than their intended use.
• Handle sharp blades and crimping dies with care to prevent injury.
• The cable tester requires a 9-volt battery. Ensure correct polarity when inserting the battery. Do not mix old and new batteries.
• Disconnect power from any cables or devices before working on them.

3. תכולת החבילה

Your PETECHTOOL RJ45 Crimp Tool Set includes the following components:

• 1 x RJ45 Pass-Through Crimp Tool
• 1 x Ethernet Cable Tester (Note: 9-volt battery not included)
• 1 x Mini Wire Stripper
• 50 x Cat6 Pass-Through RJ45 Connectors

איור 3.1: מעלview of the PETECHTOOL RJ45 Crimp Tool Set components.

4. התקנה

4.1. Cable Tester Battery Installation

The Ethernet Cable Tester requires a 9-volt battery (not included) for operation.

1. Locate the battery compartment on the back of the main (MASTER) unit of the cable tester.
2. פתחו את מכסה הסוללה.
3. Insert a 9-volt battery, ensuring correct polarity (+ and - terminals).
4. סגור היטב את מכסה הסוללה.

Figure 4.1: Cable tester with battery compartment open, indicating the need for a 9V battery.

5. הוראות הפעלה

5.1. Using the RJ45 Crimp Tool

The RJ45 Crimp Tool is designed for stripping, cutting, and crimping Ethernet and telephone cables. It features dedicated slots for 8P8C (RJ45) and 6P6C (RJ11/RJ12) connectors, along with a stripping slot for round cables and a sharp cutting blade.

איור 5.1: מפורט view of the crimp tool's functional areas.

Figure 5.2: Demonstrating the stripping, cutting, and crimping capabilities of the tool.

5.1.1. Crimping an RJ45 Connector (Pass-Through Method)

Follow these steps to create a custom-length Ethernet cable using the pass-through method:

Figure 5.3: Step-by-step guide for RJ45 pass-through crimping.

1. Unlock the Tool: First, press down on the handle to unlock the crimp tool.
2. הסרת מעיל הכבל: Insert the Ethernet cable into the stripping slot and rotate the tool to strip approximately 1 inch (2.5 cm) of the outer jacket from the end of the cable.
3. Remove Excess: Carefully cut off any small plastic or fiber strands that may be present after stripping.
4. פתחו וסדרו חוטים: Untwist the individual twisted pairs and straighten the wires. Arrange them according to the T568A or T568B wiring standard (most common is T568B: Orange/White, Orange, Green/White, Blue, Blue/White, Green, Brown/White, Brown).
5. Cut Wires Flat: Use the cutting blade on the crimp tool to cut the arranged wires flat and even, ensuring they are all the same length.
6. Insert Wires into Connector: Carefully insert the straightened and cut wires into the RJ45 pass-through connector. Push them through until the wire ends emerge from the pins at the front of the connector. Ensure each wire is in its correct channel and fully extended.
7. Insert Connector into Crimping Slot: Place the RJ45 connector, with the wires fully inserted, into the 8P8C crimping slot of the tool.
8. לחיצה על המחבר: Firmly squeeze the crimper's handles down until you can no longer go any further. The tool's ratchet mechanism will ensure a complete crimp and trim the excess wires protruding from the front of the pass-through connector.
9. לְאַמֵת: An Ethernet cable is now completed. Proceed to test the cable using the Ethernet Cable Tester.

Figure 5.4: Pass-through crimping tool in action.

5.2. Using the Ethernet Cable Tester

The Ethernet Cable Tester is used to verify the continuity and correct wiring of RJ45 (8P8C) and RJ11/RJ12 (6P6C) cables. It consists of a MASTER unit and a REMOTE unit.

Figure 5.5: Ethernet Cable Tester interface.

1. חיבור כבל: Plug one end of the Ethernet or telephone cable into the appropriate port (RJ45 or RJ11) on the MASTER unit and the other end into the corresponding port on the REMOTE unit.
2. הפעלה: Slide the power switch on the MASTER unit to either "ON S" (Slow Test) or "ON" (Quick Test).
3. שימו לב לנוריות LED: The LED indicators (1 to 8 and G for ground/shield) on both the MASTER and REMOTE units will light up sequentially.
4. פירוש תוצאות:
   • Normal Connection: LEDs on both units will illuminate in the same sequence (1-2-3-4-5-6-7-8-G).
   • מעגל פתוח: If a specific LED on either unit does not light up, it indicates an open circuit (broken wire) for that particular pin.
   • קצר: If multiple LEDs light up simultaneously or in an incorrect sequence, it indicates a short circuit between wires.
   • Crossed Wires: If the sequence of lights is different between the MASTER and REMOTE units (e.g., MASTER shows 1-2-3, REMOTE shows 1-3-2), it indicates crossed wires.
5. כיבוי: After testing, slide the power switch to "OFF" to conserve battery life.

6. תחזוקה

• ניקוי: Wipe the tools with a clean, dry cloth after each use to remove dust and debris. Do not use abrasive cleaners or solvents.
• סִיכָה: Periodically apply a small amount of light machine oil to the moving parts of the crimp tool to ensure smooth operation.
• אִחסוּן: Store the tools in a dry, cool place, away from direct sunlight and moisture, to prevent rust and damage.
• החלפת סוללה: If the cable tester's LEDs become dim or do not light up, replace the 9-volt battery. Remove the battery if the tester will not be used for an extended period.

7. פתרון תקלות

8. מפרטים

9. אחריות ותמיכה

For any problems or questions regarding your PETECHTOOL RJ45 Crimp Tool Set, please contact the manufacturer directly. The manufacturer is committed to providing prompt assistance and the best possible solution to ensure customer satisfaction.

Please refer to your purchase documentation or the official PETECHTOOL webבאתר לקבלת תנאי אחריות ספציפיים ופרטי יצירת קשר.