מָבוֹא
This manual provides instructions for the installation, operation, and maintenance of the Linear Multi-Code Keypad Transmitter, model 420001. This wireless keypad is designed for use with Multi-Code Receivers to control access to garage doors or gates.
המוצר נגמרview
The Linear Multi-Code Keypad Transmitter 420001 is a 12-button alphanumeric keypad. It operates on a 300 MHz frequency and features 10 dip switches for programming. Its weatherproof casing ensures durability for outdoor use.
תמונה: חזית view of the Linear Multi-Code Keypad Transmitter 420001, showing the 12-button alphanumeric keypad and the "MULTI-CODE" branding at the top.
התקנה והתקנה
התקנת סוללה
The keypad requires one 9V alkaline battery (not included). To install:
- Open the keypad casing.
- Connect the 9V battery to the battery clip.
- Place the battery securely within the compartment.
- Close the keypad casing, ensuring it is sealed properly for weather resistance.
הַרכָּבָה
The keypad is designed for screw-in installation and mounts with two screws.
- Choose a suitable location for mounting, ensuring it is within range of your Multi-Code Receiver.
- Mark the positions for the two mounting screws.
- קדחו חורי טייס במידת הצורך.
- Secure the keypad to the surface using appropriate screws.
תכנות לוח המקשים
This keypad uses 10 dip switches for programming. The code is entered directly through the keypad, eliminating the need to manually adjust physical dip switches on the unit itself.
- Locate the dip switch settings on your Multi-Code Receiver or existing remote. This will be a sequence of 10 switches, each set to ON, OFF, or MIDDLE (if applicable).
- On the 420001 keypad, enter the 10-digit code corresponding to your receiver's dip switch settings. Refer to the keypad's internal instructions for specific key presses to represent ON, OFF, or MIDDLE positions.
- Press the "ACCESS" button to save the code.
- Test the keypad to ensure it operates your garage door or gate opener.
פֶּתֶק: Programming typically takes less than 2 minutes. Ensure the keypad is within operational range of the receiver during testing.
הוראות הפעלה
To operate your garage door or gate using the Linear Multi-Code Keypad Transmitter:
- Enter your programmed 10-digit access code using the alphanumeric buttons.
- Press the "ACCESS" button.
- The LED indicator will illuminate, and your Multi-Code Receiver should activate, opening or closing your garage door or gate.
If the door or gate does not respond, verify your code and ensure the keypad is within effective range of the receiver.
תַחזוּקָה
- החלפת סוללה: When the keypad's performance degrades or the LED indicator fails to light, replace the 9V battery. Follow the battery installation steps.
- ניקוי: Clean the keypad's exterior with a soft, damp מטלית. הימנעו מחומרי ניקוי שוחקים או ממסים.
- עמידות בפני מזג אוויר: The keypad features a weatherproof casing. Ensure the casing is properly closed and sealed after any internal access (e.g., battery replacement) to maintain its weather-resistant properties.
פתרון בעיות
| בְּעָיָה | סיבה אפשרית | פִּתָרוֹן |
|---|---|---|
| Keypad does not respond or works intermittently. |
|
|
| מחוון LED אינו נדלק. | סוללה מתה או מותקנת בצורה לא נכונה. | Check battery connection or replace the 9V battery. |
| Keypad does not program correctly. | Incorrect dip switch settings entered. | Double-check the 10 dip switch settings from your receiver and re-enter the code carefully. |
מפרטים
| מספר דגם | 420001 |
| מותג | ליניארי |
| תֶדֶר | 300 מגה-הרץ |
| Number of Dip Switches | 10 |
| מקור כוח | סוללת אלקליין 9V אחת (לא כלולה) |
| סוג התקנה | בורג-אין |
| מידות המוצר | 6.75 x 1.5 x 3 אינץ' |
| משקל פריט | 4 אונקיות |
| חוֹמֶר | פּלָסטִי |
| צֶבַע | בז' |
| הַתאָמָה | FCC |
אחריות ותמיכה
למידע על אחריות או תמיכה טכנית, אנא עיינו במדריך הרשמי של היצרן. webאתר או צרו קשר עם מחלקת שירות הלקוחות שלהם. שמרו את קבלת הרכישה שלכם לצורך תביעות אחריות.
יַצרָן: ליניארי
