1. נגמרview
The Hobbywing QUICRUN WP 1080 is a waterproof electronic speed controller (ESC) designed for brushed motors in 1:10 scale RC cars, particularly rock crawlers and scale trucks. It features an aluminum case for enhanced cooling and is fully waterproof for use in various weather conditions. The ESC offers 15 programmable parameters, including PWM frequency and drag brake performance, which can be adjusted using the included LED program box.
תכונות מפתח כוללות:
- 100% Waterproof design.
- 15 Programmable Parameter Items for fine-tuning.
- Factory-installed XT60 Plug for battery connection.
- Automatic Throttle Calibration for ease of use.
- Powerful BEC with selectable 6V / 7.4V output at 3A.
- Supports 2-3S LiPo or 5-9S NiMh batteries.
- Included LED Program Box for convenient parameter adjustment.
תמונה 1.1: The Hobbywing QUICRUN WP 1080 ESC, LED Program Box, and an example motor. The image displays the main components of the system, including the red-finned ESC unit, the black LED program card with display and buttons, an example motor (note: this ESC is designed for brushed motors), and various connecting wires and accessories.
2. התקנה והתקנה
Follow these steps for proper installation and initial setup of your QUICRUN WP 1080 ESC.
2.1. מה בקופסה
- QUICRUN WP 1080 Speed Controller
- LED Programming Card
- מדריך הוראות
- קשרי חוט
- Double-sided Foam Tape
- צינור מכווץ חום
- גיליון מדבקות
2.2. חיבורי חיווט
- חיבור מנוע: Connect the ESC's motor wires to your brushed motor. The motor wires come tinned without connectors, allowing for direct soldering or custom connector installation. Ensure correct polarity if your motor requires it.
- חיבור סוללה: The ESC features a factory-installed XT60 plug. Connect your compatible 2-3S LiPo or 5-9S NiMh battery to this plug.
- חיבור מקלט: Plug the ESC's signal cable (usually black, red, white/orange) into the throttle channel (CH2) of your RC receiver.
- מתג הפעלה: Mount the power switch in an accessible location on your vehicle using the provided double-sided foam tape.
2.3. הרכבת מערכת ה-ESC
Use the included double-sided foam tape to securely mount the ESC to a flat surface on your RC vehicle chassis. Ensure adequate airflow around the ESC for optimal cooling, especially during demanding operation.
2.4. Automatic Throttle Calibration
Before first use, or after changing your radio system, perform an automatic throttle calibration:
- Turn on your transmitter and ensure the throttle trim is at neutral and throttle endpoints are at 100%.
- חבר את הסוללה ל-ESC.
- Press and hold the ESC's power button, then release it when the LED flashes.
- Set the throttle stick to the full throttle position and wait for the LED to flash.
- Set the throttle stick to the full brake/reverse position and wait for the LED to flash.
- Return the throttle stick to the neutral position. The ESC will emit a series of beeps, indicating successful calibration.
3. הוראות הפעלה
This section details how to operate your ESC and adjust its parameters using the LED Program Box.
3.1. פעולה בסיסית
- הפעלה: Ensure all connections are secure. Turn on your transmitter, then press the power button on the ESC.
- כיבוי: Press and hold the power button on the ESC until it turns off. Always disconnect the battery after use.
- נְהִיגָה: Use your transmitter's throttle stick to control the speed and direction of your RC vehicle.
3.2. Using the LED Program Box
The included LED Program Box allows for easy adjustment of the ESC's 15 programmable parameters. Connect the program box to the ESC's programming port (usually the fan port or a dedicated port, refer to the ESC manual for exact location) when the ESC is powered on and connected to a battery.
The program box will display the current parameter and its value. Use the "ITEM" button to cycle through parameters and the "VALUE" button to change the setting for the selected parameter. Press "OK" to save changes. Refer to the detailed instructions provided with the program box for a complete list of parameters and their functions.
Commonly adjusted parameters include:
- מצב ריצה: Forward/Brake/Reverse, Forward/Brake, Forward/Reverse.
- תאי LiPo: Auto-detect or manual setting.
- כרך נמוךtagסף חיתוך e: Protects your battery from over-discharge.
- כוח בלם גרור: Controls the braking force applied when the throttle returns to neutral.
- Initial Brake Force: Sets the minimum brake force.
- מקסימום. כוח הפוך: Adjusts the maximum speed in reverse.
- מצב התחלה (אגרוף): Controls the initial acceleration.
- תדר PWM: Adjusts the motor drive frequency for smoother low-speed control and reduced motor noise. Higher frequency can increase ESC temperature.
- BEC כרךtage: Selectable between 6.0V and 7.4V for compatibility with various servos.
4. תחזוקה
Proper maintenance ensures the longevity and optimal performance of your ESC.
- ניקוי: Despite being waterproof, it is recommended to rinse the ESC with fresh water after use in muddy or wet conditions. Ensure it is thoroughly dried before storage or next use.
- בדיקות: Regularly check all wires and connectors for signs of wear, damage, or corrosion. Ensure solder joints are secure.
- אִחסוּן: Store the ESC in a clean, dry place away from direct sunlight and extreme temperatures.
- ניטור טמפרטורה: While the ESC has thermal protection, monitor its temperature during operation, especially in demanding conditions or with high PWM frequency settings. Excessive heat can reduce lifespan.
5. פתרון תקלות
This section provides solutions to common issues you might encounter with your ESC.
| בְּעָיָה | סיבה אפשרית | פִּתָרוֹן |
|---|---|---|
| ה-ESC לא נדלק. | Battery not connected or discharged; faulty power switch; incorrect wiring. | Check battery connection and charge level. Inspect power switch and wiring for damage. |
| Motor does not respond or runs erratically. | Incorrect throttle calibration; motor wires loose or incorrectly connected; receiver signal issue. | Perform throttle calibration. Check motor wire connections. Verify receiver and transmitter are properly bound and functioning. |
| ה-ESC מתחמם יתר על המידה. | Motor too large or geared too high; high PWM frequency setting; insufficient airflow. | Check motor and gearing compatibility. Reduce PWM frequency. Ensure ESC has adequate ventilation. |
| Vehicle stops suddenly (Low Voltage Cutoff). | סוללה כרךtage dropped below cutoff threshold. | Recharge or replace battery. Adjust Low Voltage Cutoff setting if necessary (ensure it matches your battery type). |
| Program Box does not connect or display. | Incorrect connection to ESC; ESC not powered on. | Ensure program box is connected to the correct port on the ESC. Verify ESC is powered on and connected to a battery. |
6. מפרטים
Detailed technical specifications for the Hobbywing QUICRUN WP 1080 ESC.
| תכונה | פְּרָט |
|---|---|
| דֶגֶם | QUICRUN WP 1080 |
| מספר חלק | 30112750 |
| קלט סוללה | 2-3S LiPo / 5-9S NiMh |
| פלט BEC | 6V / 7.4V @ 3A (Switch Mode) |
| מגבלת מנוע (2S LiPo) | ≥10T |
| מגבלת מנוע (3S LiPo) | ≥16T |
| מידות (L x W x H) | 36.5mm x 32mm x 18mm (without fan) |
| מִשׁקָל | 58.5 גרם |
| אֲטִימוּת | כֵּן |
| ניתן לתכנות | Yes, via LED Program Box (15 parameters) |
| מחברים | XT60 (Battery, pre-installed) |
| בַּקָשָׁה | 1:10 Scale RC Cars (Brushed) |
7. אחריות ותמיכה
Specific warranty information for the Hobbywing QUICRUN WP 1080 ESC is not explicitly provided in the product details. For detailed warranty terms and conditions, please refer to the official Hobbywing website or contact your local Hobbywing distributor.
For technical support, product inquiries, or service, please visit the official Hobbywing website or contact their customer service department. Always provide your product model number (QUICRUN WP 1080) and part number (30112750) when seeking support.
רִשְׁמִי Webאֲתַר: www.hobbywing.com