גוזם מברשות בנזין Hecht 152 BTS

1. הוראות בטיחות חשובות

קרא את כל אזהרות הבטיחות, ההוראות, האיורים והמפרטים המסופקים עם כלי חשמלי זה. אי מילוי כל ההוראות המפורטות להלן עלול לגרום להתחשמלות, שריפה ו/או פציעה חמורה.

1.1 בטיחות כללית

• Always wear appropriate personal protective equipment (PPE), including eye protection, hearing protection, heavy-duty long pants, and non-slip footwear.
• הרחק ילדים, עוברי אורח וחיות מחמד במרחק של לפחות 15 מטרים (50 רגל) מאזור ההפעלה.
• Do not operate the brush cutter when you are tired, ill, or under the influence of drugs, alcohol, or medication.
• Inspect the work area for objects that could be thrown or entangled in the cutting attachment. Remove all debris.

1.2 בטיחות דלק

• יש לטפל בדלק בזהירות רבה. הוא דליק ביותר.
• Mix and store fuel in approved containers only.
• Do not smoke or allow flames or sparks near fuel or the brush cutter.
• Refuel outdoors only and wipe up any spills immediately.
• הניחו למנוע להתקרר לפני התדלוק.

1.3 בטיחות תפעול

• Hold the brush cutter firmly with both hands during operation.
• שמרו על דריסת רגל ושיווי משקל נאותים בכל עת.
• Be aware of kickback, especially when using the blade.
• Never operate without the guard properly installed.

2. המוצר נגמרview

The Hecht 152 BTS is a powerful gasoline-powered brush cutter designed for clearing dense grass and weeds. It features a 2-stroke engine and can be used with both a line spool head and a 3-tooth blade.

2.1 רכיבים

• יחידת מנוע
• Drive Shaft (disassemblable)
• Handlebar (adjustable)
• Throttle Control with Safety Lock
• שומר חיתוך
• Line Spool Head
• 3-Tooth Blade
• רתמת תרמיל
• מיכל דלק
• חבל התחלה

3. התקנה

3.1 הרכבה

1. Attach the Drive Shaft: If disassembled for transport, connect the two parts of the drive shaft securely. Ensure the locking mechanism engages.
2. התקנת הכידון: Mount the handlebar onto the drive shaft and tighten the clamping bolts. Adjust the angle for comfortable operation.
3. Mount the Cutting Guard: Secure the cutting guard above the cutting attachment. Ensure it is firmly attached to protect against debris.
4. Install Cutting Attachment: Choose between the line spool head or the 3-tooth blade. Follow the specific instructions for securing the chosen attachment. Ensure it is correctly seated and tightened.
5. Attach Backpack Harness: Connect the backpack harness to the designated attachment points on the brush cutter. Adjust straps for a snug and balanced fit.

3.2 תדלוק

The Hecht 152 BTS uses a 2-stroke engine and requires a specific fuel mixture of gasoline and 2-stroke engine oil. Refer to the engine oil manufacturer's instructions for the correct mixing ratio (typically 25:1 or 50:1).

1. הכנת תערובת דלק: Mix fresh unleaded gasoline with high-quality 2-stroke engine oil in an approved fuel container. Shake well.
2. Open Fuel Cap: Ensure the engine is cool. Carefully open the fuel tank cap.
3. מילוי מיכל דלק: Pour the mixed fuel into the tank, avoiding overfilling. Leave a small air gap.
4. מכסה מאובטח: Tightly close the fuel cap. Wipe away any spilled fuel.

4. הוראות הפעלה

4.1 התנעת המנוע

1. ראשון הקרבורטור: לחץ על נורת הפריים מספר פעמים עד שיהיה ניתן לראות דלק.
2. הגדר צ'וק: הזז את ידית הצ'וק למצב 'סגור' או 'התחל'.
3. הגדר את המצערת: Place the throttle lever in the 'START' or 'HALF THROTTLE' position.
4. Pull Starter Rope: Hold the brush cutter firmly. Pull the starter rope slowly until resistance is felt, then pull sharply and quickly. Repeat until the engine fires (usually 1-3 pulls).
5. צ'וק פתוח: Once the engine fires, move the choke lever to the 'OPEN' or 'RUN' position.
6. Restart (if necessary): If the engine stalls, repeat steps 4 and 5. If it runs, let it warm up for a few seconds before engaging the throttle fully.

4.2 עצירת המנוע

1. Release Throttle: הניחו למנוע לפעול בסרק למשך מספר שניות.
2. Press Stop Switch: Press and hold the engine stop switch until the engine completely shuts off.

4.3 טכניקות חיתוך

Always wear the backpack harness for balanced weight distribution and reduced fatigue.

• Line Trimmer Operation (430 mm cutting width): Use a sweeping motion from side to side. For automatic line feed, tap the cutting head gently on the ground while the engine is running at full throttle.
• Blade Operation (255 mm cutting width): For dense brush and small saplings, use the 3-tooth blade. Cut with a controlled, steady motion. Be aware of potential kickback.
• לשמור על שליטה: Always keep a firm grip on the handlebar and maintain good balance.

5. תחזוקה

Regular maintenance ensures optimal performance and extends the life of your Hecht 152 BTS brush cutter. Always disconnect the spark plug wire before performing any maintenance.

5.1 מסנן אוויר

1. בדוק באופן קבוע: Inspect the air filter before each use or after every 5 hours of operation.
2. ניקוי/החלפה: Remove the air filter cover. Clean the filter element with warm, soapy water, rinse thoroughly, and allow to air dry completely. If heavily soiled or damaged, replace it.

5.2 מצת

1. בדוק מעת לעת: Check the spark plug after every 20 hours of operation.
2. ניקוי/החלפה: Remove the spark plug. Clean any carbon deposits with a wire brush. Check the electrode gap and adjust if necessary. Replace if electrodes are worn or insulation is cracked.

5.3 חיתוך מצורפים

• Line Spool Head: Replace the cutting line when it runs out. Use 2.5 mm diameter line.
• להב בעל 3 שיניים: Inspect the blade for damage, cracks, or dullness before each use. Sharpen or replace the blade as needed. Always ensure the blade is balanced after sharpening.

5.4 אחסון

1. נקה ביסודיות: Clean the entire brush cutter, removing all grass, dirt, and debris.
2. ניקוז דלק: For long-term storage (over 30 days), drain the fuel tank and run the engine until it stops to clear the carburetor.
3. אחסן בצורה בטוחה: Store the brush cutter in a dry, well-ventilventilated area, out of reach of children.

6. פתרון תקלות

Before attempting any repairs, ensure the engine is off and the spark plug wire is disconnected.

7. מפרטים

8. אחריות ותמיכה

Hecht products are manufactured to high-quality standards and are guaranteed against manufacturing defects. Please retain your proof of purchase for warranty claims.

The warranty period typically covers defects in materials and workmanship under normal use. It does not cover wear and tear parts, misuse, neglect, or unauthorized modifications.

For warranty service, technical support, or to order replacement parts, please contact your authorized Hecht dealer or visit the official Hecht webאתר ליצירת קשר.

מידע ליצירת קשר:
Please refer to your purchase documentation or the official Hecht website for the most up-to-date service and support contact details in your region.