Ampמדריך למשתמש של בודק כבלי LAN robe LAN-1

1. הקדמה

ה Amprobe LAN-1 LAN Cable Tester is a diagnostic tool designed to identify and trace data cables and connectors. It helps detect common wiring issues such as shorts, miswirings, and open circuits in various cable types. This manual provides detailed instructions for the proper use, setup, and maintenance of your LAN-1 tester.

The LAN-1 evaluates most common cable types, including 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, as well as RJ45 and BNC connectors. It can test cables up to 300 meters long and uses LED indicators and an audible buzzer to signal cable status and errors.

2. מידע בטיחות

Please read and understand all safety instructions before operating the Amprobe LAN-1 LAN Cable Tester. Failure to follow these instructions may result in injury or damage to the device.

• אין להשתמש במכשיר אם הוא נראה פגום או שאינו פועל כראוי.
• Ensure the correct battery type and polarity are used during installation.
• הימנע מחשיפת המכשיר לטמפרטורות קיצוניות, לחות או לאור שמש ישיר.
• אל תנסה לתקן או לשנות את המכשיר בעצמך. יש לפנות לכל טיפול וטיפול באנשי מקצוע מוסמכים.
• Always disconnect the cable tester from any active network or power source before performing maintenance or battery replacement.

3. תכולת החבילה

ודא שכל הפריטים המפורטים להלן נמצאים בחבילה שלך:

• LAN-1 LAN Cable Tester
• (1) Remote terminator
• (1) RJ45 to female BNC cable
• (1) RJ45 to male BNC cable
• (1) RJ45 to RJ45 cable
• (1) Female BNC to female BNC cable
• (1) 9V battery (installed)
• הוראות (מדריך זה)

4. המוצר נגמרview

ה Amprobe LAN-1 features a compact design with intuitive controls and clear LED indicators for efficient cable testing.

4.1 תכונות עיקריות

• Cable Testing: Locates and traces data cables and connectors to identify shorts, miswiring, and opens.
• תאימות רב-תכליתית: Evaluates 10/100 base-T, 10 base-2, RJ45 modular, AT&T 258A, EIA/TIA 568A/568B, and Token Ring cables, along with RJ45 and BNC connectors.
• חיווי שגיאה: An audible buzzer indicates an error condition in the cable.
• טווח מורחב: Tests cables up to 300 meters long.
• תצוגה נקה: Eighteen red and green LEDs indicate the source or test results.
• מצבי בדיקה: Supports Loopback Test and Remote Test functions.
• תאימות לבטיחות: CE - EMC certified.

4.2 זיהוי רכיבים

איור 1: חֲזִית view של Amprobe LAN-1 LAN Cable Tester. This image displays the main unit with its LED pin-out indicator, battery status light, and control buttons including AUTO, MAN, HOLD, TEST, BATT, and the power button.

איור 2: Amprobe LAN-1 LAN Cable Tester showing the main unit and the remote terminator module. This view highlights how the remote unit connects to the main tester for comprehensive cable testing.

• PIN-OUT INDICATOR LEDs: Displays the wiring status for each pin (1-8) and ground (G).
• BATT LED: מציין את מצב הסוללה.
• לחצן AUTO: Initiates automatic scanning of cable pins.
• MAN Button: Allows manual step-through of cable pins.
• החזק לחצן: Pauses the current test result display.
• לחצן TEST: Starts a test cycle.
• POWER Button (Yellow): מפעיל ומכבה את המכשיר.
• יציאת RJ45: For connecting RJ45 cables.
• יציאת BNC: לחיבור כבלי BNC.
• Remote Terminator: A separate module used for testing installed cables or long runs.

5. התקנה

5.1 התקנת סוללה

The LAN-1 tester is powered by one 9V battery, which is typically pre-installed. If replacement is needed:

1. ודא שהמכשיר כבוי.
2. Locate the battery compartment cover on the back of the main unit.
3. Remove the screw(s) securing the cover and carefully open it.
4. Remove the old 9V battery and disconnect it from the terminals.
5. Connect a new 9V battery, ensuring correct polarity (+ to + and - to -).
6. הכנס את הסוללה לתא והתקן את המכסה בחזרה, תוך אבטחתו בעזרת הבורג/ים.

The battery provides power for up to 20 hours of testing.

5.2 Connecting Cables for Testing

Before testing, ensure the cable is disconnected from any active network equipment.

• For patch cables (short cables not installed in walls): Connect one end of the cable to the RJ45 or BNC port on the main unit and the other end to the corresponding port on the remote terminator.
• For installed cables (e.g., wall plates, patch panels): Connect one end of the cable to the RJ45 or BNC port on the main unit. Connect the remote terminator to the other end of the installed cable (e.g., at the wall plate in another room).

6. הוראות הפעלה

6.1 הפעלה/כיבוי

לחץ על הצהוב כּוֹחַ button to turn the device on. Press it again to turn the device off.

6.2 ביצוע בדיקה

Once the cable is connected, you can perform a test:

1. הקש על מִבְחָן button to initiate a cable test.
2. Automatic Scan (AUTO mode): הקש על AUTO button. The tester will automatically scan through each pin (1-8 and G) and display the results sequentially. This is suitable for quick checks.
3. Manual Scan (MAN mode): הקש על אָדָם button. Each press of the אָדָם button will advance the test to the next pin, allowing for a detailed examination of each connection.
4. פונקציית החזקה: הקש על לְהַחזִיק button to pause the current display of the pin-out indicator. Press it again to resume scanning.

6.3 Interpreting LED Indicators

The 18 red and green LEDs on the PIN-OUT INDICATOR provide visual feedback on the cable's status:

• נורית LED ירוקה: Indicates a correct connection for the corresponding pin.
• נורת LED אדומה: Indicates an error for the corresponding pin (e.g., open circuit, short circuit, miswiring).
• ללא LED: May indicate an open circuit or a broken wire for that pin.
• זמזם: An audible buzzer will sound when an error condition is detected, providing an additional alert.

The LEDs on the remote module will mirror the main unit's display for the corresponding pins, allowing for verification of end-to-end continuity.

6.4 בדיקת מצב הסוללה

הקש על BATT button to check the battery level. The BATT LED will illuminate if the battery has sufficient power. If the BATT LED does not light up or is dim, replace the 9V battery.

7. תחזוקה

7.1 ניקוי

To ensure the longevity and proper functioning of your LAN-1 tester, keep it clean and free from dust and debris.

• נגב את החלק החיצוני של המכשיר בעזרת חומר רך, דamp בַּד. אין להשתמש בחומרי ניקוי שוחקים או ממסים.
• Ensure no moisture enters the ports or battery compartment.

7.2 החלפת סוללה

Replace the 9V battery when the BATT LED indicates low power or if the device fails to power on. Refer to Section 5.1 for detailed battery installation instructions.

השלך תמיד סוללות משומשות בהתאם לתקנות המקומיות.

8. פתרון תקלות

אם אתם נתקלים בבעיות עם שלכם Amprobe LAN-1 LAN Cable Tester, refer to the following common problems and solutions:

9. מפרטים

10. מידע על אחריות

ה Amprobe LAN-1 LAN Cable Tester comes with a אחריות מוגבלת לשנה. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, modification, neglect, or unauthorized repair.

For specific warranty terms and conditions, please refer to the warranty card included with your product or contact Amprobe customer support.

11. תמיכת לקוחות

If you have any questions, require technical assistance, or need to report a problem with your Amprobe LAN-1 LAN Cable Tester, please contact Amprobe customer support.

אנא בקרו בפקיד Ampחָלוּק webאתר לקבלת פרטי הקשר ומשאבי התמיכה העדכניים ביותר.

משאבים מקוונים: www.amprobe.com